24/7
No heat or hot water in Richmond upon Thames, London? No heating or hot water? Tell us the boiler make and any error code and we’ll route the nearest Gas Safe engineer.
Heating helplineREPLACE_ME_HEAT_PHONE_LONDON

No Heating or Hot Water in Richmond upon Thames? Emergency Help

Prices agreed before work startsGas Safe registered for every gas jobMCS certified for heat pumpsNo-heat emergencies prioritised

Every no-heat call in Richmond upon Thames gets the same first minute: is there any smell of gas? If yes, that changes everything — off the property, call 0800 111 999. If no, we move to the boiler checks and get a Gas Safe engineer moving.

Legally required: only Gas Safe registered engineers may work on gas appliances in the UK, and No Heating or Hot Water in Richmond upon Thames, London is no exception. Every engineer carries a photo ID card you can check against the Gas Safe Register on the doorstep — ours expect to be asked, and we verify registration before assigning any job.
Richmond upon Thames heating notes: Richmond's water is hard, and the borough's larger family houses — often with multiple bathrooms and unvented systems — give scale plenty of equipment to work on. Richmond upon Thames is dominated by substantial Victorian and Edwardian family homes from Kew to Teddington, many extended and re-plumbed in layers, plus riverside properties where flood-aware heating decisions matter. Mains supply here is managed by Thames Water.

Safe checks while help is on the way

Work the outside-the-case list: thermostat turned above room temperature and programmer calling for heat; credit on a prepayment meter; other gas appliances working (a dead hob suggests a supply issue, not a boiler fault); pressure gauge at 1–1.5 bar, topped up via the filling loop if low; and in freezing weather, the condensate pipe — a frozen section thawed with warm water, then reset pressed, revives more winter boilers than any other single action. If the boiler still won't run, stop: everything further requires a Gas Safe engineer.

Heating but no hot water — or the reverse

One working and one not is diagnostically useful. On a combi, hot radiators but cold taps points hard at the diverter valve or a scaled plate heat exchanger — Richmond's water is hard, and the borough's larger family houses — often with multiple bathrooms and unvented systems — give scale plenty of equipment to work on. On a system with a cylinder, no hot water often means a motorised valve, cylinder stat or timing fault rather than the boiler itself. Either way it narrows the fault before the engineer knocks.

Why boilers fail in cold snaps

Cold weather is a stress test. Marginal pumps, tired expansion vessels and hesitant igniters all pass it in September and fail it in December. Add the condensate-freeze lockouts that arrive with the first hard frost — particularly on pipes run externally without lagging, common across St Margarets and Hampton — and the seasonal spike explains itself. A pre-winter service catches most of it early; the emergency line catches the rest.

Every no heating or hot water job in Richmond upon Thames starts with the same discipline: confirm what the customer is actually experiencing, check the system-side basics before assuming the appliance is at fault, and state the price before doing anything. It sounds obvious, and it is precisely what generates the complaints we hear about other firms.

Frequently asked questions

I can smell gas — what do I do?

Don't use the form and don't wait for us: open windows, don't operate electrical switches, get everyone out, and call the National Gas Emergency line free on 0800 111 999 immediately. Once the property is made safe, we can arrange the follow-up repair.

Is a frozen condensate pipe really that common?

In the first hard frost, it's the single most common cause of boiler lockout in the UK. The white plastic pipe running outside freezes, the boiler senses the blockage and shuts down. Warm — not boiling — water over the frozen section, then reset, restores most of them. Lagging the pipe stops the repeat.

Will you charge me a call-out just to press reset?

We try hard to prevent exactly that: the phone triage walks you through pressure, condensate, thermostat and reset checks first, free. If an engineer attends and finds a genuine fault, normal rates apply; the checks exist so you don't pay for a visit a jug of warm water would have solved.

What information should I have ready when I call?

The boiler make and model if visible, any error code on the display, whether you have gas at other appliances, the pressure-gauge reading, and your postcode. Thirty seconds of facts routes the right engineer with the right parts far better than five minutes of description.